Table of contents of the page
Then, within Swimming pool water treatment in an increase in information about What is salt electrolysis We will transmit a very relevant objective: How to control the chlorine value in a salt pool?
Salt chlorinator what is it?
What is a saline pool
Salt chlorination or salt electrolysis is an advanced sterilization and disinfection system to treat swimming pool water with saline disinfectants. (through the use of chlorine or chlorinated compounds).
1st point, what maintenance does a saltwater pool need to control the chlorine value in a salt pool?
How to perform saltwater pool maintenance
Saltwater pool maintenance
Useful guide to know how to clean the pool
Guide to maintaining a pool with water in perfect condition
Checks for maintenance of saline electrolysis:
- PH control: The ideal pH should have a value of 7,2.
- Chlorine monitoring: Check that the chlorine is between 0,5 – 1ppm. If you find low chlorine levels, the device's operating hours should be increased.
- Measure salt: Check that it is between 4 – 5 grams of salt/liter. If salt is missing, it must be added. Otherwise, empty the pool a little and renew the water.
- Check the lime level in the water
- Cleaning leaves and insects from the skimmer basket.
- Cleaning the filters.
- monthly review of the cleaning the electrodes and terminals of the cell.
- Check that there are no water leaks or air inlets.
- At the same time, verify that it is also vital to schedule enough hours of filtration to disinfect pool water, which are determined according to temperature.
MONTHLY maintenance of a salt pool: How to clean the cells of the salt chlorinators
Saltwater pool care: cell cleaning
- Although the cells of salt chlorinators have automatic cleaning, there are times when it is not enough and manual cleaning must be done.
- Therefore, we must have a periodic routine to Inspect if there is presence of lime in our pool chlorinator cell.
Saltwater pool maintenance procedure: clean the salt chlorinator cells
Guidelines for cleaning cells in saltwater pool maintenance
- The first step of the manual cell cleaning procedure will be Turn off both the pool pump and the salt chlorinator.
- Then We will disconnect the cell, unscrew it and remove it.
- Then We will wait several days for the cell to dry so that the lime plaques come off by themselves or are simply removed by giving it a few small taps. (Attention: we cannot introduce any incisive element into the cell).
- If the previous step does not work, we will have to immerse the electrodes in a solution of hydrochloric acid and water.
- As soon as the lime comes off, rinse the cell with water, dry the terminals and install the salt chlorinator again.
Saltwater pool maintenance video: cleaning the cell of the saline electrolysis equipment
Tips for saltwater pool maintenance in winter
Saltwater pool maintenance in winter
How to winterize a pool: prepare a pool for winter
Winter pool cover: perfect for winterizing the pool
Salt pool maintenance in winter
- With the intention of doing good salt pool maintenance in winter, with temperatures below 10°C the salt chlorinator must be disconnected to preserve the functioning of the electrodes and also the installation itself may deteriorate.
- So the winter saltwater pool maintenance when winter arrives, you must proceed to winterize the saltwater pool; since the temperatures are going to drop a lot and we will have to do everything possible to protect our installation from low temperatures.
- Likewise, it may be time to consider covering the pool with a cover to achieve multiple benefits and advantages.
What to do with the salt pool with green water
Saltwater pool care with green water
2nd Supervision to save the value of chlorine in salt pools: Maintain the chemical levels of the salt water pool
Ideal levels in salt water pool chemistry
- pH: 7,2-7,6
- Total chlorine value: 1,5ppm.
- Free chlorine value: 1,0-2,0ppm
- Residual or combined chlorine: 0-0,2ppm
- Ideal pool salt levels: between 4 and 7 g/l (grams per liter)
- Ideal pool ORP value (pool redox): 650mv -750mv.
- Cyanuric acid: 0-75ppm
- Pool water hardness: 150-250ppm
- Alkalinity of pool water 125-150ppm
- Pool turbidity (-1.0),
- Pool phosphates (-100 ppb)
Salt pool: keeping pH in check
What is the pH level of the pool and how to control it
What is pH: pH is a measure of acidity or alkalinity of an aqueous solution.
In this way, as we have just said, The PH is a measure of the acidity or alkalinity of the substance that indicates the concentration of hydrogen ions present in certain solutions.
Ideal pH for salt pool
pH level for acidic or alkaline salt pools
- In the case of swimming pools, Acid saltwater pool pH values range between 0 and 7,2.
- Distilled water has a pH = 7, that is, the value that is in the middle or neutral. Although in the case of the pool it would be a low pH.
- Ideal pH value for salt water pool: 7,2
- Correct pH values for salt pools: between 7,2-7,6.
- Finally, in the case of swimming pools, Base salt pool pH values range between 7,2-14.
Ideal chlorine level in saline pool according to conditions
Calculation of hours and production quantity of the salt chlorinator
Chlorine level in saltwater pools
Saline pool chlorine level
Firstly, Chlorine should have a level of 0,5 to 3ppm (I recommend being around 1pm), and the pH between 7 and 7,4 (the ideal is 7,2).
How to control the chlorine and pH level in a salt pool
How to measure ph in salt pools, how often and types of meters
How to regulate low or high ph saline pool
What to do with low or high ph in a saline pool
Master chlorine and pH salt pools
Control the chlorine level in saltwater pools manually
Comparison of chlorine and pH kits for saltwater pools
Confrontation of products to measure chlorine and pH in salt water pools
- Next, in this video you will see the correct way to use the different measurement kits for chlorine, pH, etc.
- You will also see which one suits you best according to the price, ease of use and precision of the sample.
BUY Chlorine and pH value meters in salt pools
Options for chlorine and pH level meters in saline pools
In order to get your bearings, we list the chlorine and pH level meter options and then we will show you the corresponding products.
- Drop test kit for the level of chlorine and saline pH in the pool
- Pool kit with tablets
- Salt pool test strips
- Salt pool ph and chlorine meter
- Professional pH and Chlorine Equipment
- Professional pH and chlorine equipment
- Blue Connect Go: smart water analyzer
1st Option Chlorine and pH value meters in salt pool
Buy Kit of drops analysis of chlorine and pH saline pool
Salt pool chemical drops kit price
2nd Alternative Chlorine and pH value meters in salt pool
Buy Pool pill kit, pH and free chlorine chemistry test in pills
Tablet kit price for salt pool chemistry
3rd Preference: Chlorine and pH value meters in salt pools
Buy Kit Chlorine Reactive Strips and water parameters for swimming pools and Spas
Price of test strip kit for salt pools
4th Choice Chlorine and pH value meters in salt pools
Buy Digital chlorine and pool water quality meter
Ph and chlorine meter price for salt pool
5th Suggestion: Chlorine and pH value meters in salt pools
Buy professional Chlorine and pH Analysis Detector in saline pools
Professional pH and chlorine pool and spa meter price
6th Possibility Chlorine and pH value meters in salt pool
Buy Smart water analyzer that measures the main parameters of your pool or spa
Blue Connect Go Price: Smart Pool or Spa Water Analyzer
3rd Standard for the value of chlorine in saline pool: Regularize the salt level
Pool salt level values
Ideal pool salt levels: between 4 and 7 g/l (grams per liter)
These values are appropriate for a salt electrolysis system to function properly.
- Initially, explain that the appropriate salt concentration for a pool with a salt chlorinator should be between 4 and 7 g/l (grams per liter). This means that we must add between 4 or 5 kilograms of salt for each cubic meter of water.
- In fact, a chlorinator will not operate properly below a concentration of 4 g/l or above 7
Amount of salt for swimming pools
Amount of salt for a swimming pool
How to do a saltwater pool maintenance test?
Calculate with a test how much maintenance salt a saltwater pool needs
- We take a centimeter of water from the pool and insert a salt test strip into that water.
- We will wait about 10 minutes for the test to calculate the amount of salt in the water.
- Depending on the result that appears in the test, we will know if there is a lot, little or enough salt in our pool: The salt values that a pool must have are between 5 and 6 g/cm of water.
How to calculate how much pool salt to pour?
Amount of salt pool salt chlorinator
- First of all, the amount of salt in the saline chlorinator pool will depend on what we know about the pool volume (cubic meters of water, glass capacity).
- As we have already mentioned, for every 1.000 liters of water there must be 5 kg of salt.
- So The formula is as follows: (total liters of the pool X 5)/1.000 = kg of salt
What happens if when doing the calculations we are missing one gram in the test, or what is the same as 1kg per liter of water?
- How should there really be 5kg per liter, we do the following:
- We divide the total salt that we would need for the pool by 5 and multiply everything by the kilos we need.
- That is: [(total liters of the pool X 5)/1.000] / 5 x the missing kg according to the test = kg of salt that we have to add to the pool.
Calculate how much pool salt I need
- Actually, year after year we lose salt in the pool and this means that the salt chlorinator cannot work when the salt concentrations are lower than those stipulated by the salt chlorinator manufacturer.
- For this reason, in this video we help you calculate exactly the salt you need to add to the pool each year.
Buy salinity meter in swimming pools
Pool salt concentration meter price
Salt quantity meters for swimming pools
Automatic pool salt meter price
Keep pool salinity levels at bay
Digital Salinity Meter for Saltwater Pool
Buy pool salt
Pool salt price
Buy kilos of pool salt
4th way to maintain saltwater pool maintenance: Measure Redox and maintain pool ORP value
Automatically regulate pool chlorine level for saline chlorination
What does measuring pool chlorine level mean? salt chlorination
Measurement is the function of reading the level of chlorine in the water and there are two ways to do it, with Redox regulators or through ppm.
What is the Pool Redox Reaction or Pool ORP?
- The ORP refers to abbreviations Oxygen Reduction Potential (oxidation reduction potential).
- Likewise, the ORP control factor in swimming pools It is also called: REDOX or REDOX Potential.
- In short, it is still the chemical reaction that occurs when substances exchange electrons.
- It should be noted that it is very important to know this factor since directly concerns the health of the water in our swimming pools and if it is altered it may result in a poor quality signal.
- Above all, it is very important to control the pool redox in the facilities with saline chlorination.
Ideal values orp salt pool
Saltwater Pool Maintenance for Salt Pool ORP Values
- Thus, the ideal values for the hygienic-sanitary conditions required by legislation to occur, such as The standard measurement for water in public swimming pools or spas must be a value greater than or equal to mVa 650mV – 750mV.
Video what is the ORP of salt pool water
What is a redox probe
Redox probe what is it
Redox probe for measuring pool ORP potential
- Probe for measuring ORP potential (measures oxidation and disinfection potential of chlorine or bromine) affordable.
- Thus, ORP measurements can be done easily by using a redox probe, which is nothing more than a metal electrode that has the ability to gain or lose electrons during the measurement.
Pool orp probe characteristics
- Replaceable ORP electrode with BNC connector and protective cap
- -1999 ~ 1999 mV Measurement range and ±0.1% F S ±1 digit Accuracy
- With an extra long 300cm cable, an ideal replacement probe for ORP meter, ORP controller or any ORP device which has a BNC input terminal
- The best tool for general water applications such as drinking, domestic and rain water, aquariums, tanks, ponds, swimming pools, spas, etc.
- Comes with protective case
- It can be used to connect the BNC connector directly to the ORP meter or ORP controller or to the input terminal of any ORP device with BNC input terminals.
- It allows you to flexibly measure the solution in a 300 cm container of the device and accurately determine the redox tension of the target solution to be measured.
- Replaceable ORP electrode provides reliable and easy-to-use instant ORP measurement.
- After connecting the new ORP electrode probe to the electricity input terminal, first calibrate it with a calibration solution (buffer), and then use the newly replaced ORP electrode.
- Suitable for measuring drinking water, household water and rainwater, aquariums, water tanks, ponds, swimming pools, spas, etc.
Pool orp measurement with probe
- First of all, comment that ORP probes require a very long time to "acclimatize" to the medium in which they are submerged or in other words: the measurement of an ORP probe does not stabilize until after about 20-30 minutes or even more time
- Therefore, if you made the measurement by submerging the meter for a few seconds in water, the measurement has little reliability.
- Do the test by keeping the probe submerged for between 30 and 45 minutes and then see what value it measures. If it is an "abnormal" value, it is likely that the probe is out of calibration (very common in pocket probes).
- These probes are very sensitive to electromagnetic interference from the bombs, put them as far away as possible and if not, in a separate watertight compartment as I had to do in the end.
Buy redox probe for ORP measurement
Pool redox probe price
Pool redox measuring probe
Buy Alternative to the REDOX probe
1st model: Open amperometric probes
Characteristics of probes to measure pool chlorine
Open amperometric probe for free chlorine/bromine from 0 to 10mg/l. Includes flow regulation and pH/redox electrode holder. Prepared for temperature probe. Accommodation for SEPR. 6×8 record.
Buy Open amperometric probe
Finally, if you want to buy the product click on the link: Dosim open amperometric probes for swimming pools
2nd model Potentiostatic free chlorine probe for swimming pool
This range consists of potentiostatic probes to measure free or total chlorine for applications such as:
The wide range of probes allows a better choice depending on the parameter to be tested, thus obtaining a more precise measurement.
What the potentiostatic free chlorine probe can measure
- Water treatment and conditioning
- Piscinas
- industrial applications
- Desalinated water
- The two-wire interface allows for quick and easy installation.
Buy potentiostatic probes to measure free or total chlorine for swimming pools
Probe price to control the value of chlorine in a salt pool
3rd Automatic maintenance salt pool tester
4th Electronic pool tester for pool water parameters
5th Electrolysis System for salt pool automatic maintenance
What is pool salt maintenance with automatic production system
What is the Pluma saltwater pool maintenance system?
- Saline electrolysis system with automatic production based on the chlorine reading (ORP) and water temperature. LCD display screen, high-resistance polycarbonate box and production capacities from 10 to 30 g/h. Ideal for private pools up to 160 m3.
Characteristics of the automatic production system for the maintenance of a saltwater pool
- → Latest generation power supply, with higher performance, lower electrical consumption and completely waterproof (IP67 protection)
- → Works with any type of salinity from 3 g/l to sea water (35 g/l)
- → Single button command and side switch to turn on and off
- → New ultra-efficient electrolysis cell with a useful life of 10.500 hours
- → Large LCD screen with a simple and intuitive menu
- → Temperature probe with automatic hibernation function
- → Electronic flow and coverage detector
- → Lightweight, compact and easy to install system
Buy saltwater pool system
Contact salt system company with chlorine reading included
To finish, click on the following link to visit the official page of: saline electrolysis system with automatic production based on chlorine reading (ORP) and water temperature (As a guideline, the price of private pool equipment starts at €990,00 (VAT included).