Table of contents of the page
What are the most common pool repair problems?
1st Repair of water leaks or cracks
2º Change the type of coating to obtain total watertightness of the glass
What is a pool liner? Material to cover the glass and ensure pool tightness.
- What is a pool liner?
- To begin with, among the most common pool repair problems we find the installation of a pool liner; which is a canvas made of PVC that is used to cover the inside of a swimming pool. This tarp is usually blue and is available in different sizes and shapes, for round or oval pools. Pool liners are waterproof and UV-resistant, but they may break or deteriorate with use. If any damage occurs, it must be repaired by placing specific patches.
- Thus, the pool liner is adhered using a thermo-fusion technique that seals all the joints and provides the pool with maximum watertightness.
3rd Most common pool repair problems: pool motor
The pool motor is one of the most important elements in the operation and performance of the pool.
However, there are a number of engine-related problems that sometimes occur without you knowing why. Among the most frequent we have:
The pump does not start or fails:
- This usually happens when there is some type of obstruction in the system, such as leaves or dust near the filter. In these situations it is best to disconnect the pump, clean the filter and put it back into operation.
The pump does not stop working
- This is usually due to engine wear. When this occurs, it is necessary to make a decision on whether to replace or repair the pump, since costs vary depending on each specific case and a successful result is not always obtained with repairs.
Water tends to drop in level for no apparent reason.
- : This problem is due to poor circulation of free gases. To avoid this, it is important to check the condition of the filter and check if there is any type of obstruction in the network such as remains of leaves or dust.
The controls do not seem to work correctly
- In this case, the best we can do is check all the electrical connections to verify if there are any problems, and also check the instructions in the manual to ensure that they are correctly configured.
Rusty brush blades
- Brushes are the key component to the effective operation of a pool pump. To replace the blades, you may have to remove the cover and bottom of the engine. Then you will have to clean it well and lubricate it to ensure that it works properly.
Improper or failed installation
- Another common cause of the problem is poor system installation. The pump may not be working properly because the tubing or pool filter has not been installed properly, or sometimes a connector could be leaking or connected incorrectly.
Worn parts
- If the pump motor parts wear out, you will need to replace them as soon as possible to prevent any minor problems from compromising its overall operation. You may need to replace some components such as rotors and sprocket worms to ensure the pump is working properly.
Use wear
- Among the most common problems related to the pool motor there is also usually wear and tear, which sometimes does not allow the pump to function as it should.
4º Change purification system, most common pool repair problems
Installation of a salt chlorinator
- In many cases, users decide to change the pool water disinfection system and switch, for example, to a salt chlorinator, to find greater efficiency, more savings, etc.
5th Pool skimmer repair
Most common pool repair problems: Wear of seals or gaskets
One of the most common problems you can encounter with a skimmer is wear and tear on the seals or gaskets used to make it airtight.
- If these parts become damaged, it is very likely that the skimmer will leak air into the pool. This can cause not only an unsightly mess, but also potential damage to surrounding materials in the pool and pool cover.
- In some cases, this can even lead to structural problems with your own pool if the leaks are severe enough.
Clogged skimmer
Another problem you may encounter is a clogged or malfunctioning skimmer basket.
- These devices are designed to catch leaves, twigs, and other types of debris as they float above the surface of the pool, preventing them from wrapping around the filter pump and causing damage there.
- While this feature can be incredibly useful at times, it can also lead to problems if too much debris gets trapped inside the basket. Not only does this make it more difficult for water to flow properly through the system while filtering, but it also means you have less room for your skimmer to collect unwanted items floating on top of the water before they are absorbed by your pump. .
- In some cases, your skimmer will not need more than a quick cleaning with a hose to get it working properly again.
- In other cases, you may need to install a new basket entirely, especially if it is crushed or cracked from excessive use. It's as simple as removing screws and putting in a new one or removing the entire piece and putting it back together.
Skimme wear
A less common problem you may encounter is damage or wear to the skimmer frame due to corrosion caused by water or pool chemicals.
- While these models are generally constructed of very durable materials that can withstand even extreme treatments and conditions, they can still be susceptible to deterioration over time.
- In some cases, this problem is easily fixed by simply removing one of the screws holding the skimmer in place and replacing it with a longer version that will better accommodate the additional space needed to secure the device against possible corrosion later.
Skimmer with hole or crack
- However, if the problem is more serious, such as holes or cracks in any of the structure's walls that make it difficult to maintain its airtight seal, you may need to replace the skimmer entirely.
6º Broken or failed valves
System Deterioration
- Sometimes general deterioration of the system can be the cause of the problem. The most common reasons are leaks from tubes and hoses as well as a poorly installed filter or leakage caused by an elevated tank. These problems require immediate repair to avoid further complications in the future.
7th repair PVC pool pipe
If you have a pool, chances are you need to repair the PVC pipes in your pool from time to time.
Pool pipes typically last several years, but they can become damaged or deteriorate over time.
- This can cause problems with water leaks, meaning the water level in your pool will be lower than it should be and may require additional maintenance to keep it clean.
- Fortunately, repairing a PVC pipe is easy if you have the right materials and know how to do the job correctly.
Before you start fixing your PVC pipes, there are a few things you should know about them.
First of all, there are two main types of tubes: rigid and flexible. Rigid pipe is made of solid pieces of PVC, while flexible pipe is made of a hollow tube with an inner lining.
Flexible tubing is easier to repair because it separates into segments that are easy to remove and replace, but rigid tubing can also be repaired without any problems.
- The next step in repairing your PVC pipes will be to discover the source of the problem. Sometimes you may notice damage to the outside of the tube or leaks around a fitting on the pool wall. Other times there may be obvious signs that water is seeping into the ground beneath the pool. Finding the source of the leak will help you determine what type of material you should use to repair it and how long it will take to complete the repairs.
- If your pool has missing or broken fittings, you will need another type of material to repair the PVC pipe. You can purchase special connectors that are designed to fit into existing holes and help make your plumbing system airtight again. If your pipes have tears or punctures, you can also use these special connectors on the inside of the pipes.
- However, if your pipes have splits or gaps along their length, you will probably need to use more specialized materials. Flexible repair kits are available online that allow you to patch your pipe without having to cut it open completely. These kits contain a flexible lining material as well as molding powder that allows you to fill any large gaps in the pipe before completely sealing it.
8th pool purifier repair
Sporadic checks for proper functioning of the pool purifier
In general, the main purpose of a pool filter is to clean the pool water of debris such as dust or leaves. Filtered water must be safe for humans to swim in, so the quality of the filtration system is important to ensure optimal health and hygiene conditions. Replacement filters are available at many hardware stores or specialty stores that sell pool accessories.
- Verify that there are no losses due to any breakage
- Verify that no sand accumulation at the bottom of the pool.
- Check that at the top of the tank the sand is not oily.
- Examine that in the filter tank there are no cracks.
- Examine the diffuser status.
- Check the status of the vertical tube.
- Check that when we turn off the pump the filter indicator does not stay at zero.
- Check that There is no obstruction before or after the filter.
9º Change of sand filtration material for filter glass
Glass for swimming pools It is crushed, recycled, polished and laminated glass manufactured in an ecological way.The performance of pool filter glass is far superior to sand. of traditional flint. This system has a duration from 10 years to unlimited lifeIn addition, pool glass provides us with: an ecological and recyclable way, comfort, effectiveness, quality, durability.The filtration capacity of pool glass is very effective: 20 microns.
It is also worth noting that some improvements have been made to traditional filtration materials by introducing new materials, such as activated carbon, which can be used to remove certain chemicals from water.